Ryobi CSB123 Návod k obsluze stáhnout pdf (Strana 12)

12 - English

OPERATION

DANGER:

Using a saw with a damaged cord could result in serious

injury or death. If the cord has been damaged, have it

replaced before using the saw again.

CROSS CUTTING/RIP CUTTING

See Figures 15 - 16, page 17.

When making a cross cut or rip cut, align the line of cut

with the outer blade guide notch on the base as shown in

the figure.

Since blade thicknesses vary, always make a trial cut in scrap

material along a guideline to determine how much, if any, you

must offset the guideline to produce an accurate cut.

NOTE: The distance from the line of cut to the guideline is

the amount you should offset the guide.

TO RIP CUT WITHOUT EDGE GUIDE

See Figure 16, page 17.

Use a guide when making long or wide rip cuts with the

saw.

NOTE: You may also use a edge guide to make rip cuts. Refer

to OPTIONAL EDGE GUIDE later in this manual.

Secure the workpiece.

Clamp a straight edge to the workpiece using

C-clamps.

Saw along the straight edge to achieve a straight rip

cut.

NOTE: Do not bind the blade in the cut.

BEVEL CUTTING

See Figures 17 - 18, page 17.

To make the best possible cut, follow these helpful hints.

Align the line of cut with the inner blade guide notch on

the base when making 45° bevel cuts.

Make a trial cut in scrap material along a guideline to

determine how much you should offset the guideline on

the cutting material.

Adjust the angle of the cut to any desired setting between

zero and 51.5°. Refer to TO ADJUST BEVEL SETTING

next.

TO ADJUST BEVEL SETTING

See Figure 17 and 18, page 17.

Unplug the saw.

Loosen bevel adjustment knob.

Rotate motor housing end of saw until you reach desired

angle setting on bevel scale.

Tighten bevel adjustment knob securely.

WARNING:

Attempting a bevel cut without having the bevel

adjustment knob securely tightened can result in seri-

ous injury.

TO BEVEL CUT

See Figure 19, page 17.

Hold the saw firmly with both hands as shown.

Rest the front edge of the base on the workpiece.

Start the saw and let the blade reach full speed.

Guide the saw into the workpiece and make the cut.

Release the switch trigger and allow the blade to come

to a complete stop.

Lift the saw from the workpiece.

POCKET CUTTING

See Figure 20, page 18.

WARNING:

Always adjust bevel setting to zero before making a

pocket cut. Attempting a pocket cut at any other setting

can result in loss of control of the saw possibly causing

serious injury.

Adjust the bevel setting to zero.

Set the blade to the correct blade depth setting.

Swing the lower blade guard up using the lower blade

guard handle.

NOTE: Always raise the lower blade guard with the handle

to avoid serious injury.

Hold the lower blade guard by the handle.

Rest the front of the base flat against the workpiece with

the rear of the handle raised so the blade does not touch

the workpiece.

Start the saw and let the blade reach full speed.

Guide the saw into the workpiece and make the cut.

WARNING:

Always cut in a forward direction when pocket cutting.

Cutting in the reverse direction could cause the saw to

climb up on the workpiece and back toward you.

Release the trigger and allow the blade to come to a

complete stop.

Lift the saw from the workpiece.

Clear corners out with a hand saw or sabre saw.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 47 48

Komentáře k této Příručce

Žádné komentáře

Ryobi CSB123 Návod k obsluze Strana 12

Komentáře k této Příručce

Související produkty a manuály pro Kotoučové pily Ryobi CSB123