Ryobi TSS100L Návod k obsluze

SAVE THIS MANUAL FOR FUTURE REFERENCEYour miter saw has been engineered and manufactured to our high standard for dependability, ease of operation,

10FEATURESFig. 2PRODUCT SPECIFICATIONSBlade Arbor ... 5/8 in.Blade Diameter ...

11FEATURESKNOW YOUR COMPOUND MITER SAWSee Figure 2.The safe use of this product requires an understanding of the information on the tool and in this o

12FEATURESThe following tools (not included) are needed for making adjustments or installing the blade:TOOLS NEEDEDFig. 6coMBination SQuareFraMinG SQu

13LOOSE PARTS LISTFig. 7WARNING:The use of attachments or accessories not listed might be hazardous and could cause serious personal injury. Blade W

14ASSEMBLYtrace holeS at theSe locationS For hole PatternWARNING:Do not start the compound miter saw without checking for interference between the bl

15ASSEMBLYNOTE: Many of the illustrations in this manual show only portions of the compound miter saw. This is intentional so that we can

16ASSEMBLYWORK CLAMP See Figure 11.WARNING:In some operations, the work clamp assembly may interfere with the operation of the blade guard as

17ASSEMBLYTO INSTALL / REPLACE THE BLADESee Figures 14 - 15.WARNING:A 10 in. blade is the maximum blade capacity of the saw. Never use a blade that is

18ASSEMBLYWARNING:Make sure the spindle lock button is not engaged before reconnecting saw into power source. Never engage spindle l

19ASSEMBLYREMOVING / REPLACING THE THROAT PLATESee Figure 17.WARNING:The throat plate must be below the saw table. If the throat plate is too high

2 Introduction ...

20ASSEMBLYSQUARING THE BLADE TO THE FENCESee Figures 18 - 21. Unplug the saw. Pull the saw arm all the way down and engage the lock pin to hold th

21Miter taBlecoMBination SQuareBladeMiter FenceASSEMBLYScale indicatorFig. 22indicator ScrewBeVel ScaleSQUARING THE BLADE TO THE MITER TABLESee Figure

22OPERATIONWARNING:Do not allow familiarity with tools to make you care-less. Remember that a careless fraction of a second is sufficient to i

23OPERATIONTO MAKE NON-SLIDING CUTSWARNING:Securely tighten the slide lock knob when making any non-sliding cuts. Failure to tighten the knob could re

24Fig. 28indicator PointOPERATIONTO BEVEL CUTSee Figures 28 - 29.A bevel cut is made by cutting across the grain of the workpiece with the blade angle

25OPERATIONTO COMPOUND MITER CUTSee Figures 30 - 31.A compound miter cut is a cut made using a miter angle and a bevel angle at the same time. This ty

2600OPERATIONTO SUPPORT LONG WORKPIECESSee Figure 32.Long workpieces need extra supports. Supports should be placed along the workpiece so it does not

27OPERATION WARNING:Never make a cut by pulling the saw toward you as the blade can climb on top of the workpiece and come toward you. Failu

28OPERATIONMAKING AN AUXILIARY FENCESee Figure 35.Certain unusual cuts may benefit from a thicker miter fence (auxiliary fence) due to the size and pos

29OPERATION4 PITCH OF SIDENUMBER OF SIDES0°6M- 45.00°B- 0.00°5°10°15°20°25°30°35°40°45°50°55°60°65°70°75°80°85°90°578 910M- 36.00°B- 0.00°M- 3

3GENERAL SAFETY RULESWARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire

30OPERATIONFig. 36When cutting crown molding by this method, the bevel angle should be set at 33.85°. The miter angle should be set at 31.6° either ri

31OPERATIONwronGWARNING: To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material agains

32ADJUSTMENTSWARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warning could resul

33ADJUSTMENTSTRAVEL PIVOT ADJUSTMENT The saw arm should rise completely to the up position by itself. If the saw arm does not raise by itself or i

34MAINTENANCEWARNING:When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product

35NOTES

ONE WORLD TECHNOLOGIES, INC.1428 Pearman Dairy Road, Anderson, SC 29625Phone 1-800-525-2579www.ryobitools.comWARNING:Some dust created by power sandin

4GENERAL SAFETY RULES NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes. INSPECT TOOL CORDS PERIODICAL

5 NEVER PERFORM ANY OPERATION FREEHAND. Always place the workpiece to be cut on the miter table and position it firmly against the fence as a

6SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of

7SYMBOLSThe following signal words and meanings are intended to explain the levels of risk associated with this product.DANGER:Indicates an imminently

8ELECTRICALSPEED AND WIRINGThe no-load speed of this tool is approximately 5,000 RPM. This speed is not constant and decreases under a

9GLOSSARY OF TERMSNon-Through CutsAny cutting operation where the blade does not extend completely through the thickness of the workpiece.Push