Ryobi TS1355L Uživatelský manuál

SAVE THIS MANUAL FOR FUTURE REFERENCEYour miter saw has been engineered and manufactured to our high standard for dependability, ease of operation,

10FEATURESFig. 1PRODUCT SPECIFICATIONSBlade Arbor ... 5/8 in.Blade Diameter ...

11FEATURESFig. 3KNOW YOUR COMPOUND MITER SAWSee Figure 1.The safe use of this product requires an understanding of the information on the tool and in

12FEATURESBEVEL LOCK KNOBThe bevel lock knob securely locks your compound miter saw at desired bevel angles.CROWN MOLDING STOPThe crown molding stop m

13mnLOOSE PARTS LISTFig. 6WARNING:The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.The foll

14ASSEMBLYtrace holeS at theSe locationS For hole PatternWARNING:Do not start the compound miter saw without checking for interference between the bl

15ASSEMBLYMITER LOCK HANDLESee Figure 8.To install the miter lock handle, place the threaded stud on the end of the miter lock handle into the threade

16ASSEMBLYFig. 12StoP BlockSMall wing ScrewtaBle eXtenSionFig. 13Fig. 14Fig. 15Saw vieweD FroM BottoMclaMP Bracket aSSeMBleDtaBle eXtenSionBracket SuP

17ASSEMBLYTO INSTALL / REPLACE THE BLADESee Figures 16 - 17.WARNING:A 10 in. blade is the maximum blade capacity of the saw. Never use a blade that is

18ASSEMBLYWARNING:Make sure the spindle lock button is not engaged before reconnecting saw into power source. Never engage spindle l

19ASSEMBLYFig. 20view oF Miter taBle SQuare with Fence Miter lock PlateMiter lock hanDleSliDing Miter FenceMiter taBlethroat PlateFraMing SQuareNOTE:

2 Introduction ...

20ASSEMBLYSQUARING THE BLADE TO THE FENCESee Figures 24 - 26. Unplug the saw. Pull the saw arm all the way down and engage the lock pin to hold th

21ASSEMBLYScale inDicatorFig. 27Miter ScaleinDicator ScrewBevel ScaleSQUARING THE BLADE TO THE MITER TABLESee Figures 28 - 30. Unplug the saw. Pul

22OPERATIONWARNING:Do not allow familiarity with tools to make you care-less. Remember that a careless fraction of a second is sufficient to

23Bevel ScaleFig. 32inDicator PointinDicator ScrewScale inDicatorOPERATION Loosen the miter lock handle. Rotate the miter lock handle approximately

24OPERATION When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level wi

250OPERATION Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side aga

26OPERATION4 PITCH OF SIDENUMBER OF SIDES0°6M- 45.00°B- 0.00°5°10°15°20°25°30°35°40°45°50°55°60°65°70°75°80°85°90°578 910M- 36.00°B- 0.00°M- 3

27OPERATIONWhen setting the bevel and miter angles for compound miters, remember that the settings are interdependent; changing one angle changes t

28OPERATION Bevel Angle Type of Cut Setting Left side, inside corner1. Top edge of molding against fence2. Miter table set right 31.62°3.

29OPERATIONwrongWARNING: To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material again

3GENERAL SAFETY RULESWARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fir

30ADJUSTMENTSWARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warn-ing cou

31MAINTENANCEWARNING:When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product

32MAINTENANCEFig. 46ALKALINECELLALKALINECELLALKALINECELLnegative (–)laSer guiDe SuPPortBatterieSCHANGING THE BATTERIESSee Figures 45 - 46. Unplug th

33NOTES

987000-21710-11-07 (REV:01)OPERATOR’S MANUAL10 in. Compound Miter SawTS1355L - Double InsulatedONE WORLD TECHNOLOGIES, INC.1428 Pearman Dairy Road, An

4GENERAL SAFETY RULES NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes. INSPECT TOOL CORDS PERIODIC

5 NEVER hand hold a workpiece that is too small to be clamped. Keep hands clear of the cutting area. NEVER reach behind, under, or within three

6SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of

7SYMBOLSThe following signal words and meanings are intended to explain the levels of risk associated with this product.DANGER:Indicates an imminently

8EXTENSION CORDSWhen using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to h

9GLOSSARY OF TERMSNon-Through CutsAny cutting operation where the blade does not extend completely through the thickness of the workpiece.Push