Ryobi TS1342L Uživatelský manuál

SAVE THIS MANUAL FOR FUTURE REFERENCEOPERATOR’S MANUAL10 in. Compound Miter SawTS1342L - Double InsulatedYour miter saw has been engineered and manufa

10FEATURESPRODUCT SPECIFICATIONSBlade Arbor ... 5/8 in.Blade Diameter ...

11FEATURESKNOW YOUR COMPOUND MITER SAWSee Figure 1.The safe use of this product requires an understanding of the information on the tool and in this o

12FEATURESMITER LOCK HANDLESee Figure 2.The miter lock handle securely locks the saw at desired miter angles.POSITIVE STOPS ON MITER TABLEPos

13LOOSE PARTSWARNING:The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.The following items a

14ASSEMBLYFig. 7Mounting SurFace baSetrace HoLeS at tHeSe LocationS For HoLe patterntrace HoLeS at tHeSe LocationS For HoLe patternWARNING:This saw c

15ASSEMBLYFig. 8Fig. 10to LooSenMiter Lock HandLeto tigHtenduSt bagexHauSt portbaSework cLaMpMITER LOCK HANDLESee Figure 8.To install the miter lock h

16ASSEMBLYWARNING:Make sure the spindle lock button is not engaged before reconnecting saw into power source. Never engage spindle l

17ASSEMBLYDANGER: Laser radiation. Avoid direct eye contact with light source.ALIGNING THE LASER GUIDE LINESee Figure 13.The laser guide will g

18ASSEMBLYFig. 14NOTE: Many of the illustrations in this manual show only portions of the compound miter saw. This is intentional so that we can clea

19ASSEMBLYSQUARING THE SAW BLADE TO THE FENCESee Figures 17 - 21 Unplug the saw. Pull the saw arm all the way down and engage the lock pin to hold

2 Introduction ...

20ASSEMBLYFig. 21SQUARING THE BLADE TO THE MITER TABLESee Figures 22 - 24. Unplug the saw. Pull the saw arm all the way down and engage the lock p

21OPERATIONWARNING:Do not allow familiarity with tools to make you care-less. Remember that a careless fraction of a second is sufficient to i

22Fig. 26OPERATION Rotate the control arm until the pointer aligns with the desired angle on the miter scale. Release the miter lock plate.  NOTE

23OPERATION Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece wh

24OPERATION Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece wh

25OPERATION4 PITCH OF SIDENUMBER OF SIDES0°6M- 45.00°B- 0.00°5°10°15°20°25°30°35°40°45°50°55°60°65°70°75°80°85°90°578 910M- 36.00°B- 0.00°M- 3

26OPERATIONWhen setting the bevel and miter angles for compound miters, remember that the settings are interdependent; changing one angle changes t

27OPERATIONWARNING: To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material against the

28ADJUSTMENTSWARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warning could resul

29MAINTENANCEWARNING:When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product

3GENERAL SAFETY RULESWARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire

30MAINTENANCELaSer guide SupportbatterieSCHANGING THE BATTERIESSee Figure 37. Unplug the saw.Remove the laser guide from the saw and lay it on a fl

31NOTES

• SERVICENow that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service

4GENERAL SAFETY RULES INSPECT TOOL CORDS PERIODICALLY. If damaged, have repaired by a qualified service technician at an authorized service faci

5SPECIFIC SAFETY RULES NEVER reach behind, under, or within three inches of the blade and its cutting path with hands and fingers for any reason. N

6SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Properinterpretation of t

7SYMBOLSSERVICEServicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we sug

8EXTENSION CORDSWhen using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to h

9GLOSSARY OF TERMSNon-Through CutsAny cutting operation where the blade does not extend completely through the thickness of the workpiece.Push