Ryobi TS1550 Návod k obsluze

Your new miter saw has been engineered and manufactured to Ryobi's high standard for dependability, ease ofoperation, and operator safety. Proper

10ASSEMBLYFig. 2WARNING:The miter saw should never be connected to a powersupply when you are assembling parts, making ad-justments, installing or rem

11ASSEMBLYFig. 6 Push down on the saw arm. Pull out the lock pin to release saw arm. Raise the saw arm to its full raised position.NOTE: Be cautiou

12ASSEMBLYCARRYING THE SAWSee Figure 7.Follow these directions to carry the saw. Unplug the saw.WARNING:Failure to unplug the tool could result in ac

13OPERATIONWARNING:Before starting any cutting operation, clamp or boltthe compound miter saw to a workbench at approxi-mately waist height. Never ope

14OPERATION Raise the saw arm to its full raised position. Loosen the miter lock handle by rotating it approxi-mately one-half turn. Depress the mi

15OPERATION Release the miter lock lever.NOTE: You can quickly locate 0° by releasing themiter lock lever as you rotate the control arm. Themiter lo

16OPERATIONIt may take several settings to obtain the desired cut.Always check the first angle setting after setting thesecond angle, since adjusting

174 PITCH OF SIDENUMBER OF SIDES0°6M- 45.00°B- 0.00°5°10°15°20°25°30°35°40°45°50°55°60°65°70°75°80°85°90°578910M- 36.00°B- 0.00°M- 30.00°B-

18OPERATIONCUTTING CROWN MOLDINGSee Figures 14a, 14b, and 14c.The compound miter saw is an excellent tool choice forcutting crown molding. In order to

19OPERATIONCUTTING WARPED MATERIALSee Figure 15.When cutting warped material, always make sure it ispositioned on the miter table with the convex side

2INTRODUCTION Introduction ...

20ADJUSTMENTSSQUARING THE MITER TABLE TO THEFENCESee Figures 18 through 22.Follow these directions to square the miter table to thefence. Unplug the

21ADJUSTMENTSSQUARING THE BLADE TO THE MITERTABLESee Figures 23 and 24.Follow these directions to square the blade to the mitertable. Unplug the saw.

22ADJUSTMENTSFig. 24LOCK NUTBEVELLOCKKNOBPIVOT POINTSThe following adjustments are made at the factory andnormally do not require readjustment.TRAVEL

23ACCESSORIESWARNING:To prevent accidental starting that could cause pos-sible serious personal injury, assemble all accesso-ries for the saw before c

24ACCESSORIESFig. 27Fig. 2813015304512345678910121212121212121212 Tighten the wing screw to secure the stop block to thetable extension. Make a tes

25WARNING: When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or causeproduct damage.GENERALAvoid

OPERATOR'S MANUAL12 in. (305 mm) Compound Miter SawTS1550 - Double InsulatedRYOBI TECHNOLOGIES INC.1428 Pearman Dairy Road Anderson, SC 29625Post

3RULES FOR SAFE OPERATIONSafe operation of this power tool requires that you readand understand this operator's manual and all labelsaffixed to t

4RULES FOR SAFE OPERATION KEEP HANDS AWAY FROM CUTTING AREA. Donot reach underneath work or in blade cutting pathwith your hands and fingers for any

5RULES FOR SAFE OPERATION ALWAYS STAY ALERT! Do not allow familiarity(gained from frequent use of your saw) to cause acareless mistake. ALWAYS REMEM

6SPECIFICATIONSBlade Diameter 12 in. (305 mm)Blade Arbor 1 in. (25.4 mm)No Load Speed 3600 RPMInput 120 Volts, 60 Hz, AC only, 15 ampsWeight 41 lbs. (

7UNPACKINGINFORMATIONWe have shipped the miter saw completely assembledexcept for the blade, miter lock handle, dust guide/dustbag, table extensions,

8Before using the miter saw, familiarize yourself with alloperating features and safety requirements. However,do not let familiarity with the tool mak

9FEATURESFig. 1WARNING:Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any suchalteration or modifica