Ryobi ts1341 Manuál s instrukcemi stáhnout pdf (Strana 2)

-2-

".*- *7- >7-.;<=*7- *55

27<=;>,=287< Failure to

follow all instructions listed below and in your

miter saw manual may result in serious

personal injury.

>55B *<<.6+5. *7- =201=.7 *55 =1.

/*<=.7.;< ;.:>2;.- /8; =12< <=*7- 5<8

;.6.6+.; =8 8,,*<287*55B ,1.,4 =1.

<=*7- *7- 6*4. <>;. 2= 2< <=255 =201= A

loose stand is unstable and may shift in use

and cause serious injury.

$>;7=885<@2=,18//*7--2<,877.,=98@.;

+./8;. 68>7=270 =8=1. <=*7- Unintended

startup during assembly can cause injury.

./8;.89.;*=2706*4.<>;.=1..7=2;.>72=

2< 95*,.- 87 * <852- /5*= 5.?.5 <>;/*,.

Serious injury could occur if tool with stand is

unstable and tips.

.?.;<=*7-87=8858;2=<<=*7-8;><.*<

5*--.; 8; <,*//85-270 Serious injury could

occur if the tool is tipped or the cutting tool is

accidentally contacted. Do not store

materials on or near the tool such that it is

necessary to stand on the tool or its stand to

reach them.

%<. 875B 8<,1 ;.95*,.6.7= 9*;=< Any

others may create a hazard.

The Miter Saw should be firmly mounted to

the stand per the instruction manual.

After mounting the Miter Saw to the stand,

align, position and balance the Miter Saw per

the instruction manual.

Before use, verify that all stand parts are free

from damage and/or deformity.

Before use, verify that all parts or

components of the stand are properly

installed.

Before use, swing open each of the legs until

the pin clicks, locking the legs in position.

When mounting the Miter Saw to the stand,

make sure that the tool mounting brackets

are in the “UNLOCK” position, so the tool

mount will engage with the rails. Be sure to

hold the saw until it is secured to prevent it

from falling off the rails. Mounting bracket

locking knobs should then be tightened.

When removing the Miter Saw from the stand

“UNLOCK” the mounting bracket. Hold the

Miter Saw firmly to prevent the saw from

falling off the rails. Carefully remove the Miter

Saw.

Do not modify the stand in any manner or

use the stand for any purpose other than is

stated in these instructions.

Because cut material may cause the stand to

become unbalanced, always be sure the

material is supported properly. Also, if the

piece being cut is placed far beyond the work

support, stand legs on the opposite side may

suddenly be lifted up due to weight

imbalance. To prevent this from occurring,

hold the opposite side firmly before cutting.

WARNING

698;=*7=#*/.=B7<=;>,=287</8;%<270$12<2=.;#*@#=*7-

$12<$2=.;#*@#=*7-2<-.<207.-=8+.><.-@2=1

=1./8558@2708<,162=.;<*@<

Other units may be compatible, but have not been verified for use with the GTA3800 system.

8<,1

4212, 4212L, 4410, 4410L,

4412, 4405, 5412L, 3912,

3915, 3918, 3924, 5312,

4310, GCM12SD

.5=*

36-255, 36-255L, 36-240,

MS450

.'*5=

DW712, DW705S, DW703,

DW708, DW706, DW718,

DW715, DW716, DW709

*42=*

LS1214, LS1221, LS1013,

LS1212, MS1214F

25@*>4..

6497-6, 6955-20, 6950-20

"2-02-

MS1065LZ, MS1250LZ

"B8+2

TS1353DXL, TS1341, TS1552

BM 2610013406 06-10:BM 2610013406 06-10 6/14/10 9:52 AM Page 2

1 2 3 4 5 6 7 ... 39 40

Komentáře k této Příručce

Žádné komentáře

Ryobi ts1341 Manuál s instrukcemi Strana 2

Komentáře k této Příručce

Související produkty a manuály pro Kotoučové pily Ryobi ts1341