Ryobi CS1800 Návod k obsluze

SAVE THIS MANUAL FOR FUTURE REFERENCEYour miter saw has been engineered and manufactured to our high standard for dependability, ease of operation, an

10FEATURESFig. 3KNOW YOUR COMPOUND MITER SAWSee Figure 1.The safe use of this product requires an understanding of the information on the tool and in

11FEATURESSPINDLE LOCK BUTTONSee Figure 3.The spindle lock button locks the spindle stopping the blade from rotating. Depress and hold the lo

12LOOSE PARTS LISTFig. 6WARNING:The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.The follow

13ASSEMBLYWARNING:Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possib

14ASSEMBLYFig. 8WARNING:Always make sure the compound miter saw is securely mounted to a workbench or an approved workstand. Failure to heed this warn

15WARNING:Assemble the saw head to the base before attempting to use the product. Using the saw head without first install-ing it to the base may resu

16ASSEMBLYDUST BAGSee Figure 12.A dust bag is provided for use on this miter saw. It fits over the exhaust port on the upper blade guard. To install,

17ASSEMBLYDANGER:Laser radiation. Avoid direct eye contact with light source.WARNING:Use of controls or adjustments or performance of pro-cedur

18note: before use, repLace screw and tighten secureLY to prevent guard MoveMentASSEMBLYTO INSTALL/REPLACE THE BLADESee Figures 16 - 17.WARNING:A 7-1/

19ASSEMBLYFig. 18view of Miter tabLe square with fence Miter Lock LeverMiter tabLethroat pLate squareNOTE: Many of the illustrations in this manual sh

2 Introduction ...

20ASSEMBLYSQUARING THE BLADE TO THE FENCESee Figures 21 - 24. Unplug the saw. Pull the saw arm all the way down and engage the lock pin to hold th

Miter tabLesquarebeveL Lock knobMiter fencebLade21ASSEMBLYscaLe indicatorMiter scaLeindicator screwbeveL scaLeSQUARING THE BLADE TO THE MITER TABLESee

22OPERATIONWARNING:Do not allow familiarity with tools to make you care-less. Remember that a careless fraction of a second is sufficient to

23OPERATION NOTE: You can quickly locate 0°, 15°, 22-1/2°, left or right, 31.62° and 45° left or right as you rotate the control arm. The miter table

24OPERATION Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side agai

250OPERATION Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side aga

26OPERATION4 PITCH OF SIDENUMBER OF SIDES0°6M- 45.00°B- 0.00°5°10°15°20°25°30°35°40°45°50°55°60°65°70°75°80°85°90°578 910M- 36.00°B- 0.00°M- 3

27OPERATIONWhen setting the bevel and miter angles for compound miters, remember that the settings are interdependent; changing one angle changes the

28OPERATIONWARNING: To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material against the

29ADJUSTMENTSWARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warning could resul

3GENERAL SAFETY RULESWARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fir

30ADJUSTMENTSDANGER:Laser radiation. Avoid direct eye contact with light source.WARNING:Use of controls or adjustments or performance of pro-ce

31MAINTENANCEWARNING:When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.W

987000-9521-14-10 (REV:01)OPERATOR’S MANUAL7-1/4 in. Compound Miter SawTS1141 - Double Insulated• SERVICENow that you have purchased your tool, shoul

4GENERAL SAFETY RULES NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes. INSPECT TOOL CORDS PERIODICAL

5SPECIFIC SAFETY RULES NEVER hand hold a workpiece that is too small to be clamped. Keep hands clear of the cutting area. NEVER reach behind, unde

6SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of

7ELECTRICALDOUBLE INSULATIONDouble insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire groun

8GLOSSARY OF TERMSPush Blocks (for jointer planers)Device used to feed the workpiece over the jointer planer cutterhead during any operation. This aid

9FEATURESFig. 1PRODUCT SPECIFICATIONSArbor .................. 5/8 in.Blade Diameter ....